How To Repair Or Replace Swimming Pool Light
Download Commodity
Download Commodity
Typically, backyard swimming pools are equipped with 1 or more underwater lights. Just like any lite, the seedling tin burn out and will need to be replaced. There is no need to lower the water level in your pool to supercede the burned-out bulb. Instead, you can remove the light housing from the side of the pool, pull the fixture upwardly onto the side of the pool, and alter the light seedling at that place.
-
1
Close off all power to the puddle lighting. Yous'll exercise this at your home'southward circuit breaker box. 1 of the breakers should exist marked "pool." Switch this breaker into the "off" position to turn off all electricity to the pool.[1]
- Some swimming pools have been equipped with their own breaker boxes. If you don't see a "puddle" breaker in your master electrical box, look around virtually your pool to see if there's a 2nd box nearby.
-
2
Cheque to brand sure power is off past trying to turn on the pool lights. Yous don't want to risk possible electrocution, so flip the pool lights on and off to make sure the puddle isn't receiving whatever electrical power.
- If yous only have one pool light, attempt switching the pool pump on and off. If the power is truly off, the pump won't turn on.
Ad
-
3
Remove the single screw at the acme of the fixture. This spiral, chosen the "screwlock," is the only thing holding the lite fixture to the pool wall. In nearly all cases, this will be a large Phillips-caput screw, and then you will need a Phillips screwdriver to remove it. Whorl up your sleeves, stick your arm beneath the surface of the water, and unscrew the screwlock.[2]
- If the low-cal is low on the side of your puddle, or if your arm is too short to reach, you lot'll have to get into the pool to unscrew the screw-lock and remove the fixture.
- Once yous've unscrewed the screwlock, place it someplace where it won't curlicue away and go lost. A shirt pocket is a good choice.
-
4
Pry the light fixture out of the niche box with a flat-head screwdriver. Most calorie-free fixtures volition have a tab at the lesser which allows yous to pull the fixture away from the wall. Piece of work this tab loose with the apartment-head screwdriver. Also use the screwdriver to loosen the fixture in a few other locations.[3]
- In one case information technology's loose enough, work your fingers in and pull the calorie-free fixture out of the wall.
-
v
Pull the pool lighting fixture up onto the puddle decking. There should be enough of cord coiled up in the niche box to let you to lift out the fixture and movement it to the deck. Slowly draw the fixture and the cord behind it up onto the pool deck and gear up information technology on the concrete surface.[4]
- If the string isn't unraveling, reach into the wall behind the light fixture and give the cord 2-3 abrupt tugs.
Advertisement
-
1
Remove the comprehend and lens from the calorie-free fixture. The method will vary based on the historic period of your puddle. Older pool models volition accept screws that need to be removed to let you to pull out the lens. Newer puddle lights will most likely take tabs that need to be pried loose. Remove the lens and gear up it aside in a rubber place. Practise the same with the safety gasket that sits betwixt the lens and the metal fixture.[v]
- Brand certain that you don't splash any water into the fixture when you remove the lens and gasket.
-
2
Purchase a replacement bulb identical to the bulb in the low-cal. Consult your pool's handbook or user manual to discover out the verbal type of seedling the fixture requires. And then, pay a visit to a local pool-supply store and buy the corresponding bulb. Make certain that the size, make, and serial numbers of the ii bulbs friction match.[vi]
- If yous can't find the exact seedling y'all need in a pool-supply store, purchase the bulb online. You can purchase replacement pool bulbs through major online retailers or through the pool manufacturer'due south website.
- If you're worried that the light fixture may exist leaking, yous can likewise purchase a new rubber gasket to seal the fixture and prevent h2o from getting in.
-
three
Unscrew the former bulb and spiral the new one into place with a towel. Once the lens and gasket are out of the way, you'll be able to reach in and grasp the 3 in (seven.6 cm) bulb. Twist the bulb counterclockwise to unscrew it. One time you lot've removed it, hold onto the new bulb with a towel. Identify the bulb in the center of the fixture and twist information technology clockwise.[7]
- Never directly touch on the lightbulb. The oils on your fingers tin can damage a halogen bulb and cause information technology to burn out apace.
- Dispose of the old bulb safely by throwing it in a trash can.
-
iv
Turn the power on for 2-iii seconds to examination the light and see if information technology works. Go back to the excursion billow or pool electric box and flip the switch back to "on." Come across if the calorie-free turns on. If information technology does, immediately turn the switch dorsum to "off." This volition save you the hassle of installing the new bulb only to find out that it doesn't piece of work.[eight]
- If y'all get out the pool low-cal on for longer than 5 seconds, the bulb may burn itself out. Element of group vii bulbs like those used in puddle lights are extremely hot. If yous turn the low-cal on without cool water surrounding it, it will quickly overheat and burn out.[9]
Advertisement
-
1
Supersede the lens and reassemble the fixture. Identify the gasket and the lens back in place roofing the bulb.[10] As you're putting the parts of the low-cal fixture back together, apply the edge of your towel to dry whatsoever water that's dripped into the fixture.
-
2
Supplant all screws and lock in all tabs to close the calorie-free fixture. You'll but reverse the disassembling process to re-assemble the pool calorie-free fixture. If you removed small screws from the fixture while y'all were taking it apart, at present's the time to spiral those back into identify. Tighten them and then that the gasket is pressed flat betwixt the lens and fixture comprehend.[eleven]
- If you're dealing with a newer model puddle light fixture that doesn't accept screws, make certain that the tabs are all firmly pushed into position so that the fixture is sealed close.
-
3
Place the fixture back into low-cal niche and screw in the top screw. Hold the fixture in your manus and achieve below the surface of the water. Insert the fixture back into the niche that you withdrew it from earlier. Take the screw-lock screw and insert it back into the hole at the height of the fixture. Then, use your Phillips head screwdriver to tighten the spiral into position.[12]
- You'll too need to feed the cable back into the wall if you lot had to tug it out. An like shooting fish in a barrel style to do this is to wrap the string 3-4 times effectually the base of the fixture before y'all insert it into the wall.
-
four
Turn the power back on by switching the circuit breaker to "on." This volition restore electricity to the puddle lite. In one case the circuits are continued once more, turn the light on to make sure it is working correctly.[13]
- If the light still isn't working correctly, you may be dealing with a more serious electrical problem. In this case, contact the pool'south manufacturer and ask them to send a repair specialist to inspect the pool.
Advertisement
Add New Question
-
Question
Do y'all have to arrive the water to practise this?
Not necessarily. If you can reach the screw property the light assembly in identify from outside the pool, yous don't accept to get into the pool to change the light.
-
Question
Do I accept to drain a pool to alter the light bulb?
You do not have to bleed the pool if you can remove the calorie-free assembly.
-
Question
The screw-in LED lights in my pool piece of work, only there's mold growing within them. Tin I make clean them?
Yes. Follow the steps on how to remove the lite, and be sure to turn off the breaker first. If the earth surrounding your LED is sealed, and there are no tabs or screws holding the slice together, place the light in a ii% bleach concentrate for 24 hours. Follow that past letting the light sit in the sun, non submersed in water, for several days or until the condensation is gone. If there are no screws or tabs, use RTV sealant (caulk) at the seam, and allow to dry prior to re-installing. If it is a ii slice, substitute the RTV caulk stride by replacing the O-ring and re-tighten the bolts or screws.
-
Question
My light is working, but seems to be moving around a flake. The "tab" you lot reference at the bottom, side by side from the spiral, may take come up out or become loose. What tin can I practice?
They make a wedge just for that. Any pool store should accept information technology or be able to gild it for you if information technology'due south not in stock.
-
Question
What size breaker in amps is needed to run ane puddle and one spa light if a twenty amp breaker keeps tripping?
You have the right size; there is a break in the wiring between the billow and the light/switch used to turn the light off/on, or a leak in one of your lights. In order to stop the billow from tripping, you'll need to decide the source of the ability "going to ground" (an electrician can help diagnose this problem). Putting a bigger breaker in identify of the old ane ensures only i of 2 things -- more than damage to the electrical components or severe injury to you or anyone who comes in contact with the water.
-
Question
I need to replace the spiral that holds the lamp. Should I utilise brass or stainless steel?
ConnorFisher
Community Answer
Use contumely. Stainless steel screws will corrode rather quickly when submerged underwater, while brass screws will non corrode.
-
Question
Why is my pool calorie-free bulb fading from dim to vivid?
ConnorFisher
Customs Reply
This could be acquired by diverse issues. Open up the fixture and brand certain there isn't whatsoever h2o inside backside the lens. Dry the lens if it is wet. The dimming seedling may also demand to exist replaced.
-
Question
How practice I alter a puddle low-cal if the tabs and screws are corroded and broken?
ConnorFisher
Community Respond
You may demand to use a pair of pliers to unscrew or pull out the screw and tabs. When you reinstall the light fixture, be certain to use contumely screws (not stainless steel). Y'all may need to replace the entire fixture, depending on how bad the corrosion is.
-
Question
I have brown spots that are spreading in my pool and they don't come off when I brush them. What could they exist?
We have those temporary brown stains every autumn from dropping acorns. It dissolves on its own in a few days.
-
Question
Tin can I get colour bulb or lens cover?
I would imagine that that would exist possible as long as they are the right size.
Show more answers
Ask a Question
200 characters left
Include your email accost to become a bulletin when this question is answered.
Submit
Advertizement
Video
Thank you for submitting a tip for review!
-
Afterward you have replaced the bulb, make sure you don't bump or driblet it. The filament in the seedling is fragile and might break.
-
Practise non reattach the lens when you examination the replacement bulb. Leaving the lens off will let heat to dissipate so as not to fissure the lens.
-
Practice non attempt to alter the light until you are admittedly sure the pool lighting circuit is asunder. If the circuit is still active, you could be seriously hurt by the electrical current.
-
If your lens is equipped with tabs, take care not to damage the waterproof gasket when prying upward the lens.
Advertising
Things You'll Need
- Replacement seedling
- Phillips-head screwdriver
- Flat-headed screwdriver
- Towels
About This Article
Article Summary X
To change a puddle calorie-free, start by shutting off all power to the pool using your abode's circuit billow. Then, remove the screw at the superlative of the lighting fixture and use a flat-caput screwdriver to pry the fixture out of the niche box. Next, unscrew or pry the cover and lens off the fixture and replace the old bulb with a new identical one. Finally, supervene upon the lens, reassemble the fixture, and spiral the fixture back into the niche box. To learn how to purchase a replacement seedling for your pool light, scroll downward!
Did this summary aid you?
Thank you to all authors for creating a page that has been read 438,660 times.
Did this commodity aid you?
Source: https://www.wikihow.com/Change-a-Pool-Light
Posted by: lealayed1960.blogspot.com
0 Response to "How To Repair Or Replace Swimming Pool Light"
Post a Comment